• NG体育娱乐,ng体育平台

    双极性晶体管

    二极管

    ESD保护、TVS、滤波和信号调节ESD保护

    MOSFET

    氮化镓场效应晶体管(GaN FET)

    绝缘栅双极晶体管(IGBTs)

    模拟和逻辑IC

    汽车应用认证产品(AEC-Q100/Q101)

    74LVC162245ADL

    16-bit transceiver with direction pin; 30 Ohm series termination resistors; 5 V tolerant input/output; 3-state

    The 74LVC162245A; 74LVCH162245A is a 16-bit transceiver with 30 Ω termination resistors and 3-state outputs. The device can be used as two 8-bit transceivers or one 16-bit transceiver. The device features two output enables (1OE and 2OE) each controlling eight outputs, and two send/receive (1DIR and 2DIR) inputs for direction control. A HIGH on nOE causes the outputs to assume a high-impedance OFF-state. Inputs can be driven from either 3.3 V or 5 V devices. This feature allows the use of these devices as translators in mixed 3.3 V and 5 V environments.

    Schmitt-trigger action at all inputs makes the circuit tolerant of slower input rise and fall times.

    This device is fully specified for partial power down applications using IOFF. The IOFF circuitry disables the output, preventing the potentially damaging backflow current through the device when it is powered down.

    The 74LVCH162245A bus hold on data inputs eliminates the need for external pull-up resistors to hold unused inputs.

    此产品已停产

    Features and benefits

    • Overvoltage tolerant inputs to 5.5 V

    • Wide supply voltage range from 1.2 V to 3.6 V

    • CMOS low power consumption

    • Multibyte flow-through standard pin-out architecture

    • Low inductance multiple power and ground pins for minimum noise and ground bounce

    • Direct interface with TTL levels

    • Integrated 30 Ω termination resistors

    • IOFF circuitry provides partial Power-down mode operation

    • All data inputs have bus hold (74LVCH162245A only)

    • Complies with JEDEC standard:

      • JESD8-7A (1.65 V to 1.95 V)

      • JESD8-5A (2.3 V to 2.7 V)

      • JESD8-C/JESD36 (2.7 V to 3.6 V)

    • ESD protection:

      • HBM: ANSI/ESDA/JEDEC JS-001 class 2 exceeds 2000 V

      • CDM: ANSI/ESDA/JEDEC JS-002 class C3 exceeds 1000 V

    • Specified from -40 °C to +85 °C and from -40 °C to +125 °C

    参数类型

    型号 Package name
    74LVC162245ADL SSOP48

    PCB Symbol, Footprint and 3D Model

    Model Name 描述

    封装

    下表中的所有产品型号均已停产 。

    型号 可订购的器件编号,(订购码(12NC)) 状态 标示 封装 外形图 回流焊/波峰焊 包装
    74LVC162245ADL 74LVC162245ADL,118
    (935237690118)
    Withdrawn / End-of-life LVC162245A SOT370-1
    SSOP48
    (SOT370-1)
    SOT370-1 SSOP-TSSOP-VSO-REFLOW
    SSOP-TSSOP-VSO-WAVE
    SOT370-1_118
    74LVC162245ADL,112
    (935237690112)
    Obsolete LVC162245A 暂无信息

    环境信息

    下表中的所有产品型号均已停产 。

    型号 可订购的器件编号 化学成分 RoHS RHF指示符
    74LVC162245ADL 74LVC162245ADL,118 74LVC162245ADL rohs rhf rhf
    74LVC162245ADL 74LVC162245ADL,112 74LVC162245ADL rohs rhf rhf
    品质及可靠性免责声明

    文档 (8)

    文件名称 标题 类型 日期
    74LVC_LVCH162245A 16-bit transceiver with direction pin; 30 Ohm series termination resistors; 5 V tolerant input/output; 3-state Data sheet 2024-04-22
    AN11009 Pin FMEA for LVC family Application note 2019-01-09
    AN263 Power considerations when using CMOS and BiCMOS logic devices Application note 2023-02-07
    lvc162245a lvc162245a IBIS model IBIS model 2013-04-08
    Nexperia_package_poster Nexperia package poster Leaflet 2020-05-15
    SOT370-1 plastic, shrink small outline package; 48 leads; 0.635 mm pitch; 15.9 mm x 7.5 mm x 2.8 mm body Package information 2020-04-21
    SSOP-TSSOP-VSO-REFLOW Footprint for reflow soldering Reflow soldering 2009-10-08
    SSOP-TSSOP-VSO-WAVE Footprint for wave soldering Wave soldering 2009-10-08

    支持

    如果您需要设计/技术支持,请告知我们并填写 应答表 我们会尽快回复您。

    模型

    文件名称 标题 类型 日期
    lvc162245a lvc162245a IBIS model IBIS model 2013-04-08

    PCB Symbol, Footprint and 3D Model

    Model Name 描述

    How does it work?

    The interactive datasheets are based on the Nexperia MOSFET precision electrothermal models. With our interactive datasheets you can simply specify your own conditions interactively. Start by changing the values of the conditions. You can do this by using the sliders in the condition fields. By dragging the sliders you will see how the MOSFET will perform at the new conditions set.

    NG体育娱乐,ng体育平台